电源:外部供电
最大电流:6 A
模拟输出电压范围:0 V 至 10 V
总线连接器:PXI Express
2通道,10 V,6 A PXI可编程电源
ONETEST 欢迎您
厂商登录 | 入驻
登录 | 注册 购物车 微信公众号厂商登录
电源:外部供电
最大电流:6 A
模拟输出电压范围:0 V 至 10 V
总线连接器:PXI Express
2通道,10 V,6 A PXI可编程电源
以下指标取自 Teledyne 官方在线规格书,按原文档小节分组。
| CH <0..1> + | HI force terminal connected to channel power stage (generates and/or dissipates power). Positive polarity is defined as voltage measured on HI > LO. |
| CH <0..1> - | LO force terminal connected to channel power stage (generates and/or dissipates power). Positive polarity is defined as voltage measured on HI > LO. |
| CH <0..1> Sense + | Voltage remote sense input terminals. Used to compensate for I*R voltage drops in cable leads, connectors, and switches. |
| GND | Tied to chassis ground through module front panel. Use for connections to cable shields or grounding the LO force terminal. |
| Terminal 0 + | Positive Auxiliary Power Input |
| Terminal 1 - | Negative Auxiliary Power Input |
| DC voltage Voltage range 10 V | Voltage range |
| Voltage range | 10 V |
| Minimum programmable voltage level/limit | 0.03 V |
| DC current Current range 6 A Minimum programmable current level/limit 0.02 A | Current range |
| Current range | 6 A |
| Minimum programmable current level/limit | 0.02 A |
| Output power | 60 W/channel |
| Voltage programming | 0.32 mV† |
| Voltage measurement | 3 mV‡ |
| Current programming | 0.19 mA† |
| Current measurement | 2 mA‡ |
| Voltage (per amp of output load) | 0.5 mV |
| Current (per volt of output change) | 0.25 mA |
| Rise time (measured from 10% to 90% of programmed voltage change from 0.03 V to 10 V with specified load) Full resistive load (1.67 Ω). <10 ms, typical No load <10 ms, typical | Full resistive load (1.67 Ω). |
| Full resistive load (1.67 Ω). | <10 ms, typical |
| No load | <10 ms, typical |
| Fall time (measured from 90% to 10% of programmed voltage change from 10 V to 0.03 V with specified load) Full resistive load (1.67 Ω) <10 ms , typical No load <10 ms, typical | Full resistive load (1.67 Ω) |
| Full resistive load (1.67 Ω) | <10 ms , typical |
| No load | <10 ms, typical |
| Transient response | <200 μs to recover within 100 mV of voltage level after a load current change from 50% to 100% of current range, typical |
| Settling time Rise time (time to settle within 0.1% of final programmed voltage level from 0.03 V to 10 V with specified load) Full resistive load (1.67 Ω) 25 ms, typical No load 25 ms, typical Fall time (time to settle within 0.1% of final programmed voltage level from 10 V to 0.03 V with specified load) Full resistive load (1.67 Ω) 25 ms, typical No load 25 ms, typical | Rise time (time to settle within 0.1% of final programmed voltage level from 0.03 V to 10 V with specified load) Full resistive load (1.67 Ω) 25 ms, typical No load 25 ms, typical |
| Rise time (time to settle within 0.1% of final programmed voltage level from 0.03 V to 10 V with specified load) Full resistive load (1.67 Ω) 25 ms, typical No load 25 ms, typical | Full resistive load (1.67 Ω) |
| Full resistive load (1.67 Ω) | 25 ms, typical |
| No load | 25 ms, typical |
| Fall time (time to settle within 0.1% of final programmed voltage level from 10 V to 0.03 V with specified load) Full resistive load (1.67 Ω) 25 ms, typical No load 25 ms, typical | Full resistive load (1.67 Ω) |
| Full resistive load (1.67 Ω) | 25 ms, typical |
| No load | 25 ms, typical |
| Voltage[3] Peak-to-peak <18 mV, typical RMS <3 mV, typical | Peak-to-peak |
| Peak-to-peak | <18 mV, typical |
| RMS | <3 mV, typical |
| Current, RMS[4] | <2 mA, typical |
| Line regulation (per volt of change in the auxiliary power input) Voltage 0.2 mV Current 0.5 mA | Voltage |
| Voltage | 0.2 mV |
| Current | 0.5 mA |
| Maximum output lead drop | Up to 1 V drop per lead |
| Maximum sense lead resistance | Up to 1 Ω per lead |
| Output channel protection Overcurrent or reverse voltage Reverse clamp diode, protected by thermal overload circuit Overtemperature Automatic shutdown | Overcurrent or reverse voltage |
| Overcurrent or reverse voltage | Reverse clamp diode, protected by thermal overload circuit |
| Overtemperature | Automatic shutdown |
| Auxiliary power input protection Overvoltage, typical >52.8 VDC shut-off Overcurrent or reverse voltage Fused | Overvoltage, typical |
| Overvoltage, typical | >52.8 VDC shut-off |
| Overcurrent or reverse voltage | Fused |
| Voltage from auxiliary power + to earth ground | 60 VDC |
| Voltage from auxiliary power - to earth ground | 1 VDC |
| Isolation voltage, channels 0- and 1-to-earth ground[5] Continuous 150 VDC, CAT I Withstand 800 Vpk | Continuous |
| Continuous | 150 VDC, CAT I |
| Withstand | 800 Vpk |
| PXI power requirement | 0.5 A from 3.3 V rail, 0.25 A from 12 V rail |
| Auxiliary power source input requirements | 45.6 VDC to 50.4 VDC,3.5 A max |
| Measurement rate Default 60/s (Line frequency set to 60 Hz, aperture set to 1 PLC, measure record mode), nominal Maximum 5,250/s, nominal | Default |
| Default | 60/s (Line frequency set to 60 Hz, aperture set to 1 PLC, measure record mode), nominal |
| Maximum | 5,250/s, nominal |
| Types | Start Source Sequence Advance Measure |
| Sources (PXI trigger lines 0 to 7)[6] Polarity Active high (not configurable) Minimum pulse width 100 ns | Polarity |
| Polarity | Active high (not configurable) |
| Minimum pulse width | 100 ns |
| Destinations[7] (PXI trigger lines 0 to 7)[6] Polarity Active high (not configurable) Minimum pulse width 200 ns | Polarity |
| Polarity | Active high (not configurable) |
| Minimum pulse width | 200 ns |
| Types | Source Complete Sequence Iteration Complete Sequence Engine Done Measure Complete |
| Destinations (PXI trigger lines 0 to 7)[6] Polarity Active high (not configurable) Pulse width 230 ns | Polarity |
| Polarity | Active high (not configurable) |
| Pulse width | 230 ns |
| Dimensions | 3U, one-slot, PXI Express/cPCI Express module; 2.0 cm × 13.0 cm × 21.6 cm (0.8 in. × 5.1 in. × 8.5 in.), nominal |
| Weight | 443 g, nominal |
| User-replaceable fuse, auxiliary power input (PCB-mount) | F 6.3 A H 250 V (5 × 20 mm ceramic fuse) |
| Front panel connectors Output channels Phoenix Contact, 5.08 mm (10 position) Auxiliary power input Weidmuller, 3.5 mm (2 × 2 position) | Output channels |
| Output channels | Phoenix Contact, 5.08 mm (10 position) |
| Auxiliary power input | Weidmuller, 3.5 mm (2 × 2 position) |
官方规格书:https://www.ni.com/docs/en-US/bundle/pxie-4113-specs/page/specs.html
NI官方渠道
官方渠道(官网 / 热线 / 邮箱)
官方渠道(中国大陆)
• 官网 www.ni.com/zh-cn
• 在线选购 www.ni.com/zh-cn/shop.html
• 经销商查询
官网「查找经销商」 www.ni.com/zh-cn/shop/advisors.html
• 联系方式
NI 中文官网不公布中国区电话与邮箱,报价、技术支持、校准、维修一律通过官网在线表单提交(「联系我们」页)
全国办事处
公司总部
• NI(National Instruments)
• 地址
11500 N Mopac Expwy, Austin, TX 78759-3504, United States
• 母公司
Emerson(2023 年完成收购,NI 隶属艾默生测试与测量业务集团)
0条提问
X
提问
X
回答
发表口碑
AI问答