是德科技 | KEYSIGHT
N2756A 测试电缆组件 详细指标
The N2756A is a low-cost 16-channel MSO cable kit for InfiniiVision Series oscilloscopes
– Wide operating temperature range of –40 to +85 °C for extreme temperature
environmental chamber testing
– 400 MHz bandwidth (–3 dB)
– High impedance (10 MΩ at DC) input
– Wide input range: 1 kV CAT II
600 V CAT III
– Includes hook tip adapters (x2), ground leads (x2) and spring ground tip (x1)
The N7007A
400 MHz passive probe is a low-cost, high impedance passive probe with
rugged probe tips for environmental chamber testing from –40 to +85 °C. Its large
input impedance (10 MΩ at DC) and wide input voltage range (1,000 Vdc + peak AC
CATII) makes the probe ideal for a broad range of general purpose extreme temperature
条件:Operating humidity range < 90% at 40 °C
Bandwidth 400 MHz (with spring ground)
70 MHz (with ground lead)
Input impedance (at DC) 10 MΩ/15.5 pF (when terminated into
1 MΩ)
Oscilloscope compensation range
6 to 18 pF
Operating temperature range
–40 to +85 °C
Max input range 1 kV CAT II
600 V CAT III
N7007A 10:1
400 MHz extreme temperature passive probe
N7006A Spring ground for N7007A
N7008A Hook tip adapter for N7007A
N7009A Ground lead for N7007A
N7006A spring ground
N7008A hook tip adapter
N7009A ground lead
N7007A Extreme temperature passive probe
– Ideal for measuring up to 3.7 kV
– Up to 500 MHz bandwidth
– 100:1 attenuation
10076C high-voltage probe
The Keysight 10076C 3.7 kV
100:1 passive probe gives you the voltage and bandwidth
you need for making high-voltage measurements. Its compact design makes it easier to
probe today’s small power electronics components and its rugged construction means it
can withstand rough handling without breaking
Risetime (calculated) <
0.7 ns
Input resistance 66.7 MΩ (when terminated into
1 MΩ)
Input capacitance Approx
3 pF
Maximum input 3700 Vpk, 2650 Vrms
2650 Vdc (mains isolated)
1000 Vpk CAT II (post receptacle mains)
Compensation
6 to 18 pF range
Operating temperature
0 °C to 50 °C
Ordering information for Keysight high-voltage probes
10076C High-voltage probe: includes one retractable hook tip, one ground-bayonet, one IC probing tip, one alligator ground lead, one spring ground tip and a compensation screwdriver
10077A Accessory kit for 10076A/C: includes one retractable
pincher tip, one ground lead, one insulation cap, two measuring pins, and two
N2789A Spring ground tip for 10076B/C
10076C passive probe
10077A accessory kit for 10076C
10076C derating curve
High-voltage Passive Probes
N2789A spring ground clip for 10076B/C
1130B-34B InfiniiMax
– 1.5 to 7 GHz InfiniiMax probe system
– InfiniiMax probe amplifier supports both differential- and single-ended measurements for a more cost- effective solution
– Unrivaled InfiniiMax probing accessories support browsing, solder-in, and socketed use models at the maximum performance available
– Compatible with 3000 X/T-,
4000 X-, 6000 X-, 5000
6000, and
7000 Series oscilloscopes (except for
6000 Series
100-MHz models)
The InfiniiMax
1130B Series probe
amplifier is a perfect complement to the
InfiniiVision
1 GHz or higher bandwidth
models. Its bandwidth, extremely low input capacitance (0.32 pF), high common mode rejection, and patented resistor probe tip technology provide ultra low
loading of the DUT and superior signal fidelity. Keysight’s innovative InfiniiMax
1130B Series differential probe is the easiest-to-use, highest performance
probing system available for high-speed digital design, and represents a new industry standard for accuracy, flexibility, and reliability. Designers can achieve full
Probe bandwidth (–3 dB) 1134B: >
7 GHz
Rise and fall time (10 to 90%) 1134B
60 ps
Input capacitance Cm =
0.1 pF Cm is between tips
Cg =
0.34 pF Cg is ground for each tip
Cdiff =
0.27 pF differential mode capacitance = Cm + Cg/2
Cse =
0.44 pF single-ended mode capacitance = Cm + Cg
Input resistance Differential mode resistance = 50 kΩ
± 2%
Single-ended mode resistance = 25 kΩ
± 2%
Input dynamic range
± 2.5 V
Input common mode range ± 6.75 Vdc to 100 Hz; ± 1.25 V >
100 Hz
Maximum signal slew rate
18 V/ns when probing a single-ended signal
30 V/ns when probing a differential signal
DC attenuation 10:1
± 3% before calibration on oscilloscope
10:1
± 1% after calibration on oscilloscope
Offset range
± 12.0 V when probing single-ended signal
Maximum input voltage
30 Vpeak, mains isolated
ESD tolerance > 8 kV from 100 pF
300 Ω HBM
Maximum number of probes supported by 3000 X/T-/
5000/6000/7000 Series
Maximum number of probes supported by
4000 X- and 6000
Keysight 1130B InfiniiMax probe offers you the highest performance available for measuring
differential and single-ended signals
InfiniiMax Active Probes and Accessories
1130B-34B InfiniiMax high-performance active probe system
Ordering information for Keysight InfiniiMax
1130B Series probe and accessories
Probe amplifier 1130B 1.5 GHz InfiniiMax probe amplifier (order one or more probe heads or connectivity kits per amplifier) 1131B 3.5 GHz InfiniiMax probe amplifier (order one or more probe heads or connectivity kits per amplifier) 1132B
5 GHz InfiniiMax probe amplifier (order one or more probe heads or connectivity kits per amplifier)
1134B
7 GHz InfiniiMax probe amplifier (order one or more probe heads or connectivity kits per amplifier)
E2669B InfiniiMax connectivity kit for differential/single-ended measurements
E2668B InfiniiMax connectivity kit for single-ended measurements
条件:Osclloscope Probes, Accessories, and Options data sheet with Keysight literature number 5968-7141EN.
E2675B InfiniiMax differential browser probe head and accessories
E2676B InfiniiMax single-ended browser probe head and accessories
E2677B InfiniiMax differential solder-in probe head and accessories
E2678B InfiniiMax single-ended/differential socketed probe head and accessories
E2679B InfiniiMax single-ended socketed probe head and accessories
N2851A QuickTip probe head for InfiniiMax I/II probe amp
N2849A QuickTip tips for N2851A
N5380B InfiniiMax II differential SMA head
N5425B/N5426A
12-GHz differential ZIF solder-in probe head and ZIF probe tips
N5451A InfiniiMax long-wire ZIF probe tips (for use with N5425B ZIF probe head)
N5450B InfiniiMax extreme temperature extension cable (that allows for probing in environments from —55 to +150 °C)
N2880A InfiniiMax in-line attenuator kit (pairs of 6 dB
12 dB and 20 dB attenuator in a kit)
N2881A InfiniiMax DC blocking caps (a pair of 30 Vdc blocking cap)
For more comprehensive information about the 1130B InfiniiMax probe amplifier and its accessories, refer to the Keysight Infiniium
InfiniiMax solder-in probe head with long wires InfiniiMax ZIF tip soldered on board InfiniiMax browser head
InfiniiMode probes and accessories
N2750A
1.5 GHz InfiniiMode differential
N2751A
3.5 GHz InfiniiMode differential
条件:Each probe includes two solder-in tips, two socketed tips and two browser tips.
N2752A
6 GHz InfiniiMode differential probe
N2776A Differential browser tips (qty
3)
N2777A InfiniiMode solder-in tips (qty
3)
N2778A InfiniiMode socketed tips (qty
3)
N4822A Socketed tip for USB/Ethernet
application fixtures (qty
1)
InfiniiMode Active Probes and Accessories
N2750A-52A InfiniiMode probe
– 1.5 to 6 GHz bandwidth
– Dual attenuation ratio (2:1/10:1)
– InfiniiMode probing for making differential, single-ended and common mode measurements with a single probe
– Built-in quick action scope control for quick access to a variety of scope functions
– AutoProbe interface for auto configuration and probe power
The N2750A Series InfiniiMode differential
probe is a new generation of low-cost, differential active probe compatible with
InfiniiVision 3000 X-, 4000 X-
6000
The N2750A Series InfiniiMode probe
offer
2:1 and 10:1 dual attenuation
settings, allowing them to be used for a broad range of applications. Dual attenuation range is automatically configured depending on the size of the
The new differential probe has an input resistance of 200 k Ω (differential) or 100 kΩ (each input to ground), and an extremely low input capacitance of 700 fF
to minimize circuit loading
条件:these probes can be used in a wide variety of analog signal measurements as well.
This, accompanied with superior signal fidelity, makes these probes useful for most digital design and debug applications. And with their wide dynamic
range (10 Vpp) and offset range (
± 15 V)
The N2750A comes with new InfiniiMode
operation modes. The InfiniiMode allows convenient measurements of differential, single-ended, and common mode signals with a single probe tip without
reconnecting the probe to change the connection. The N2750A probe’s
– B – ground (single-ended B)
– (A+B)/2 – ground (common mode)
Quick action scope control
The N2750A Series InfiniiMode probe
provides convenient and quick access to various functions on the scope. You often have a need to control the scope while you hold a probe in your hand. With
the quick action scope control feature built into the probe, you can turn the built-in headlight of the probe on and off, or control some frequently used scope
functions such as RUN/STOP, auto scale, quick print, and quick save with only a button press on the probe. Get control of your most needed function with a push
of the quick action control button on the probe
条件:probes are equipped with a white LED headlight to illuminate the circuit under test which will help you see where you are probing.
Flexibility in probe use models is also a vital necessity. The probes come standard with three different types of exchangeable probe tips that allow for easy connections
to the circuit under test. These probe tips enable you to access multiple signals on anything from header connectors to hard-to-reach, high-density circuitry. The
This probe is compatible with InfiniiVision 3000 X-Series with software ver. 2.2 or above, 4000 X-Series with software ver.
3.01 or above, and 6000 X-Series with
Characteristics and specifications for N2750A Series InfiniiMode probes
适用型号型号编号 N2750A N2751A N2752A
条件:X-Series 1. Denotes warranted electrical specifications at 2:1 attenuation mode after 20 minute warm-up. All others are typical. 2. When calibrated on the oscilloscope, these characteristics are determined by the oscilloscope characteristics. 3. Assumes symmetric differential signals.
Probe bandwidth 1 (–3 dB) 1.5 GHz 3.5 GHz
6 GHz
Rise time, probe only (10 to 90%) 233 ps 100 ps
58.3 ps
Input resistance (at DC) 1 200 kΩ
± 2% (differential mode)
100 kΩ
± 2% (single-ended mode)
Input capacitance
700 fF (with browser)
Attenuation ratio (at DC)
2:1 / 10:1
Input dynamic range ± 1 V, 2 Vpp (at 2:1) / ± 5 V, 10 Vpp (at
10:1)
Input common mode range ± 15 V (from DC to 100 Hz), ± 2.5 V (for >100 Hz)
3
Maximum non-destructive input voltage
± 30 V (DC + peak AC)
Maximum number of probes supported by 3000 X-Series
1
Maximum number of probes supported by 4000 X-
6000
For more information about the N2750A Series InfiniiMode probes, refer to the data sheet with the Keysight literature number,
5991-0560EN.
N2750A with browser tip N2750A with socketed tip N2750A with solder-in tip
InfiniiMode Active Probes and Accessories (Continued)
High-Voltage Differential Active Probes – DP0001A
High-Voltage Differential Probe
条件:transient pulse with as fast as 1.2 nsec of edge speed in modern switching power supplies.
– High voltage differential probe for high voltage, high speed power device testing
– Measure up to 2 kV mains isolated
1 kV CAT III and 400 MHz
– Unmatched electrical performance - flat frequency response and high CMRR
The DP0001A is a
400 MHz high voltage differential probe with 2 kV mains isolated or 1 kV
CAT III rating designed for making accurate high-voltage power measurements required
for testing today’s WBG power devices, power converters or motor drives. Thanks to
high bandwidth and low loading characteristics, the probe can accurately measure
1 kV
Also, high CMRR simplifies the measurement challenges found in noisy, high common-
mode power electronics environments
条件:with a 50-Ω AutoProbe interface, which configures the scope for the probe automatically.
The probe is compatible with InfiniiVision 3000TX, 4000X and 6000X models.
Characteristic Value measured at the four supported attenuation modes
When used with an InfiniiVision oscilloscope, the probe provides four manually switchable
modes of attenuation to make low noise measurement at high V/div settings. The
differential probes have a differential input resistance of 10 MΩ and low input capacitance
of 2 pF to minimize circuit loading. The DP0001A is compatible with Keysight oscilloscopes
When probing differential signals inside of environmental chambers at extreme
temperatures, Keysight offers the N7013A extreme temperature extension kit. The N7013A
is compatible with the DP0001A with a de-rated bandwidth of 70 MHz. The
70 cm long
differential cable set and accessories can operate in temperatures ranging from -40 degC
to +85 degC.
Frequency response of DP0001A
Probe bandwidth (-3 dB)
400 MHz 400 MHz 400 MHz
400 MHz
Risetime (10% - 90%)
Input voltage 50 V 1.2 nsec 1.2 nsec 875 psec
875 psec
Input voltage 500 V Not Applicable Not Applicable 1.2 nsec
1.2 nsec
Input voltage 1000 V Not Applicable Not Applicable Not Applicable
1.2 nsec
Mains isolated *
2000 Vrms
6000 V Overvoltage Transient
Noise (Vrms ‡ / spectral density) (Referred to the input) 180 mV / 9 μV/rt (Hz) 180 mV / 9 μV/rt (Hz) 280 mV / 14 μV/rt (Hz)
300 mV / 15 μV/rt (Hz)
Typical propagation delay
10 ns
Maximum differential input voltage (DC + AC peak) ± 200 V ± 400 V ± 1000 V
± 2000 V
Common mode voltage
± 2000 Vpk (1400 Vrms)
DC gain accuracy ± 0.7 % ± 0.7 % ± 0.35 %
± 0.35 %
Offset drift ** 150 μV / °C 150 μV / °C 40 μV / °C
40 μV / °C
条件:* Mains isolated is for measurements performed on circuits not directly connected to a mains supply.
† Measurement category III is for measurements performed in the building installation.
Each input to ground 5 MΩ ||
4pF
Differential Input Impedance 10 MΩ ||
2pF
Input coupling of the oscilloscope †† AutoProbe Interface
50 Ω
Typical CMRR (dB) DC > 80 > 80 > 80 >
80
Standard accessories Spring tips (qty 4), contact pins (qty 10), probe tip adapters (qty 2), safety alligator clips (qty
2)
alligator plunger clips (qty 2), spade terminals (qty 2), pincer clips (qty 2), hook tip adapters (qty
2)
Max number of probes supported 1 (with 3000TX), 4 (with
4000X and 6000X)
‡ Broadband Noise, Bandwidth
400 MHz.
DP0001A
400 MHz high voltage differential probe
DP0002A Accessory kit for DP0001A
N7013A Extreme temperature probing kit for differential probe, probe BW derated to <
70 MHz with the
High-voltage Differential Active Probes
– 25 to 800 MHz bandwidth
– Measure up to 1,400 V CAT II and 7 kV mains isolated
N2790A/91A and N2891A high voltage differential probes
Oscilloscope users often need to make floating measurements where neither point
of the measurement is at earth ground. Use N2790A, N2791A, or N2891A high
voltage differential probes to make safe and accurate floating measurements with an
oscilloscope. The N2790A, N2791A, and N2891A high voltage differential probes allow
conventional earth-grounded Keysight oscilloscopes to be used for floating signal
条件:The N2791A and N2891A are compatible with any oscilloscope with 1 M Ω BNC input.
Each probe offers user-selectable attenuation settings that makes it highly versatile,
allowing it to be used for a broad range of applications. The probe comes with probe tip
accessories for use with small and large components in tight spaces.
The N2791A and N2891A probe power is supplied by included
4x AA batteries or USB
host port of the scope or PC via a supplied USB power cable. The N2790A is compatible
with the Keysight’s AutoProbe interface where the probe power is supplied by the
适用型号 N2790A N2791A N2891A
条件:extended into the environmental chamber under extreme-temperature conditions
Bandwidth 100 MHz 25 MHz
70 MHz
Risetime 3.5 ns 14 ns
5 ns
Attenuation ratio 50:1 / 500:1 10:1 / 100:1
100:1 / 1000:1
CMRR —80 dB at 50/60 Hz —80 dB at 50/60 Hz
–80 dB at 50/60 Hz
—50 dB at 1 kHz —40 dB at 1 MHz
–60 dB at 20 kHz
—50 dB at 1 MHz
Input impedance (between inputs) 8 MΩ / 3.5 pF 8 MΩ / 8 pF
100 MΩ / 5 pF
Max input voltage to ground ± 1000 V (CAT II) ± 700 V at 100:1 ± 7000 V at 1000:1 ± 600 V (CAT III) ± 70 V at 10:1
± 700 V at 100:1
Max input voltage between two inputs ± 1400 V at 500:1 ± 700 V at 100:1 ± 7000 V at 1000:1 ± 140 V at 50:1 ± 70 V at 10:1
± 700 V at 100:1
Max number of probes supported by
3000
X-/4000 X-/6000 X-/
5000/6000/7000 Series
N7013A extreme temperature extension cable kit
The N7013A is a
70-cm long extreme temperature extension cable kit compatible with
four of Keysight’s medium- and high-voltage differential active probes, including the
DP0001A, N2790A, and N2791A. These probes are typically used in power supply
testing applications, as well as testing automotive differential buses including CAN, CAN
FD, and FlexRay. With the N7013A extension kit, the main body of the temperature-
sensitive differential active probe can be placed outside of the environmental chamber,
while the extension kit (70-cm long cable pair) and connection adapters can be
ranging from -40 to +85 °C.
The N7013A kit includes:
– 1 pair of extreme-temperature differential extension cables
– 1 pair of extreme-temperature hook tip adapters
– 1 pair of extreme-temperature banana-to-socketed tip adapters for connecting to
0.025” square pins
The N7014A accessory includes
1 pair of banana-to-socketed tip adapters
Temperature range
—40 to +85 °C
Derated bandwidth DP0001A, N2790A
70 MHz
Derated bandwidth with N2791A
25 MHz
High-voltage Differential Active Probes (Continued)
N7013A Extreme Temperature Probing Kit
N7014A Banana-to-socketed tip adapter
High-voltage Differential Active Probes (Continued)
条件:class D amplifiers, vehicle bus measurements, and high-speed digital system designs.
response even while using the extension leads and probe tip accessories.
probe tip accessories for use with small and large components in tight spaces.
N2804A/N2805A high-voltage, high-speed differential probes
The N2804A and N2805A differential probes provide the superior general-purpose
differential signal measurements that are required for high-speed power measurements
such as measuring characteristics of switching power devices, DC-DC converters or
The N2804A 300-MHz differential probe offers
100:1 attenuation ratio, allowing it to be
used adequately for high voltage signal measurements. The differential probe has a
differential input resistance of 4 M Ω and low input capacitance of 4 pF to minimize
circuit loading. The probe comes with a pair of extension leads (30 cm long) with a
damping resistor built-in to damp out the in-band resonance and provide flat frequency
The N2805A is a
200-MHz differential probe designed to provide superior differential
signal measurements with a long cable length (5 m), making it ideal in an environment
where extended cable length is required. This probe comes with an extensive set of
Characteristics for N2804A and N2805A
Bandwidth 300 MHz (without extension leads)
200 MHz
120 MHz (with extension leads)
Attenuation ratio 100:1
50:1
CMRR —80 dB at 50/60 Hz
—75 dB at 50/60 Hz
—75 dB at 1 MHz
—80 dB at 1 MHz
Input impedance (between inputs) 4 MΩ // 4 pF 4 MΩ //
4 pF
Max input voltage (between two inputs) ± 300 V (DC+ peak AC) and
± 200 Vrms
± 200 V (DC+ peak AC) and
± 200 Vrms CAT II
Max input voltage
± 300 V (DC+ peak AC) and
± 200 Vrms CATII
± 500 V (DC+ peak AC) and
± 500 Vrms mains isolated
± 1000 V (DC+ peak AC) and
± 1000 Vrms CATI
± 300 V (DC+ peak AC) and
± 200 Vrms CATII
Max number of probes supported by InfiniiVision
Compatible InfiniiVision oscilloscopes 6000X Series, 4000X Series with software ver. 4.0 or higher
3000X
Series with software ver.
2.38 or higher
For more information about the N7020A power rail probe, refer to the Keysight data
sheet with the publication number
5992-0141EN.
N2804A
300 MHz differential probe
N2805A
200 MHz differential probe
High-voltage Differential Active Probes (Continued)
DP001xA Series differential active probes
The DP001xA Series of differential probes provide the superior general-purpose
differential signal measurements required for today’s high-speed power-related
measurements such as motor drives, automotive differential bus measurements, and
条件:from 250 MHz to 1.7 GHz with a wide input range and probe offset range up to ± 60 volts.
The DP001xA Series differential active probes are available in bandiwdth models ranging
The DP001xA Series probes are equipped with Keysight Technologies’ AutoProbe1
interface that provides power and DC offset to the active circuitry of the probe’s
differential amplifier, as well as automatic attenuation settings based on the
oscilloscope’s vertical scale setting. These probes are compatible with most of Keysight’s
InfiniiVision X-Series and Infiniium oscilloscopes that provide selectable
50-Ω input
terminations with the AutoProbe1 interface. Select from the following models to meet
适用型号 DP0010A/DP0011A/DP0012A/DP0013A
Bandwidth 250 MHz/ 500 MHz/ 1.0 GHz/
1.7 GHz
± 8.4 Vpk on
17:1 auto attenuation
± 42 Vpk on
85:1 auto attenuation
Input impedance (between inputs) 1.7 MΩ //
0.9 pF
Max input voltage to ground
± 60 V
Ordering information for Keysight high voltage differential probes,
N2790A 100 MHz
1.4 kV differential probe with AutoProbe interface
N2791A 25 MHz
700-V differential probe
DP0001A 400 MHz
2,000 V differential probe with AutoProbe I interface
DP0010A 250 MHz
42 V differential probe with AutoProbe I interface
DP0011A 500 MHz
42 V differential probe with AutoProbe I interface
DP0012A 1 GHz
42 V differential probe with AutoProbe I interface
DP0013A 1.7 GHz
42 V differential probe with AutoProbe I interface
N2891A 70-MHz
7,000-V differential probe
N2804A
300 MHz high voltage differential probe
N2805A
200 MHz high voltage differential probe with extended cable length
N2816A Probe tip accessory kit for N2804A including 2 alligator clips
2 pincer clips, and
2 extension leads (30 cm)
N2817A Probe tip accessory kit for N2805A including 2 alligator clips, 2 hook clips
2 pincer
clips, and 2 browser tips
DP0002A Probe tip accessory kit for DP0001A
N7013A Extreme temperature extension cable kit for N2790A, N2791A, and DP0001A
N2790A 100-MHz
1.4-kV differential probe
N2791A 25-MHz
700-V differential probe
DP0013A 1.7 GHz
42 V differential active
DP001xA Series probe using socketed Y-lead
适用型号型号编号 N2795A N2796A N2797A
Probe bandwidth 1 (–3 dB) 1 GHz 2 GHz
1.5 GHz
Risetime 350 ps 175 ps
233 psec
System bandwidth
500/600 MHz with
条件:Max number of probes supported by InfiniiVision 4000X, 6000X 1. Denotes warranted electrical specifications after 20 minute warm-up, all others are typical.
2. The N2797A is compatible with 3000 X/T-, 4000 X- and 6000 X-Series only.
Infiniium
1 GHz with 1 GHz
InfiniiVision 3000 X
4000 X
1 GHz with Keysight’s
1 GHz
InfiniiVision/Infiniium
1.5 GHz with
Keysight’s
1.5 GHz InfiniiVision
Attenuation ratio (at dc) 10:1
± 0.5%
Input dynamic range
–8 to +8 V (DC or peak AC)
Non-destructive input voltage
–20 to +20 V
DC offset error (output zero)
± 1 mV
Low frequency accuracy 0.5% at 70 Hz
1 Vpp
Max number of probes supported by InfiniiVision
3000
X-/5000/6000/7000 Series
2
N4839A Dual lead socketed adapter, 6 cm, qty
2
N4840A Dual lead solder-in adapter, 5 cm, qty
2
N4841A Dual lead socketed adapter, 9 cm, qty
2
N4842A Dual pin PCB header, qty
2
N4843A Solderable tips, qty
10
N4844A Right angle ground lead, 5 cm, qty
2
N4845A Ground blade, qty
2
N4846A Offset ground, qty
2
single-ended active voltage
条件:Infiniium Autoprobe interface, eliminating the need for an additional power supply.
The probes also come with a number of accessories that allow for easy connections to the circuit under test.
For more information about N2795A/96A/97A active probe, refer to the Keysight
N2795A/96A/97A active probe data sheet, literature number
5990-6480EN
The N2795A/96A/97A are equipped
with a white LED headlight to illuminate the circuit under test. The probes are powered directly by the InfiniiVision and
– High resistance (1 MΩ) and low
capacitance (1 pF) input for low
– Wide input dynamic range (
± 8 V) and
offset range (
± 12 V for N2796A/97A
± 8 V for N2795A)
– Direct connection to AutoProbe interface (no power supply required)
– N2797A for extreme temperature
environmental chamber testing at
条件:probes with the AutoProbe interface (compatible with Keysight’s InfiniiVision and Infiniium family of oscilloscopes).
characterization, and educational research applications. Its 1 M Ω input resistance and extremely low input capacitance (1 pF) provide ultra low loading of the DUT.
This, accompanied with superior signal fidelity, makes these probes useful for most of today’s digital logic voltages.
–40 to +85 °C
The N2795A/96A are a new generation of
low-cost
1 to 2 GHz single-ended active
These probes integrate many of the characteristics needed for today’s general- purpose, high-speed probing–especially in digital system design, component design/
Testing devices over extreme temperature ranges is quite common these days. The
N2797A
1.5 GHz single-ended active probe
is the industry’s first low-cost high input impedance active probe with rugged probe tips for environmental chamber testing of ICs and devices. It gives the ability
to probe signals at drastic temperature swings ranging from –40 to +85 °C. The probe provides a
2 m long cable. Order
N2798A for re-ordering accessories.
Single-ended Active Probes (Continued)
N7020A power rail probe
– 2-GHz single-ended active probe for power rail noise measurement
– 1.1:1 attenuation ratio ensures low noise signal measurement
–
± 24 V of probe offset range enables effective elimination of DC component of a
条件:enables users to measure small signals riding on top of DC power rails.
The N7020A power rail probe is a low noise, large offset range oscilloscope probe that
– Low noise: The N7020A power rail probe is a
1:1 attenuation ratio active probe. As
a general rule, the higher a probes attenuation ratio, the nosier the signal will be on
条件:– Large offset range: The N7020A power rail probe provides ± 24 V of probe offset.
This enables users to center the signal on screen while placing the oscilloscope at
its 最大值 vertical 灵敏度和 zoom · 开信号
– Low DC loading: The N7020A power rail probe has
50 kΩ input impedance at DC
minimizing the probe’s DC loading of the power rail
– Large input dynamic range: The N7020A power rail probe’s
± 850 mV input dynamic
range means that users can measure up to
± 850 mV deviations of their DC
supplies. This is very useful for measuring programmable supplies like those used in
microcontroller power saving modes
– Supporting three connection options — pigtail solder head (2 GHz), SMA (2 GHz),
and browser (350 MHz).
N7020A power rail probe
N7023A browser kit (now included in the
N7020A or orderable separately)
Probe bandwidth (—3 dB)
2 GHz
Input impedance at DC
50 kΩ
Input dynamic range
± 850 mV
Probe noise
10% of oscilloscope noise
Included accessories N7021A coaxial probe head (qty.
3), N7022A SMA main cable
N7023A browser kit
Max number of probes supported by InfiniiVision
Compatible InfiniiVision oscilloscopes 3000X/T-Series with software ver. 2.38 or higher 4000 X-Series with software rev.
4.0 or higher
6000 X-Series with software rev.
6.10 or higher
For more information about the N7020A power rail probe, refer to the Keysight data
sheet with the publication number
5992-0141EN.
Characteristics for Keysight
54620-68701, N6450-60001
N6459-60001 logic probes
Characteristics for Keysight
01650-61607 logic probe
N2756A 16 ch 4 x
4 MSO cable kit
X Series MSO. Includes 18 grabbers
5 right angle grounds, and 5 ground extension leads
N2755A 8 ch 2 x
4 MSO cable kit
for 2000 X Series MSO.
Includes 9 grabbers
3 right
angle grounds, and 3 ground
extension leads 01650-61607
40-pin (F) to 40-pin (F) logic probe cable
– Compatible with all
40-pin logic
MSO probes offer great value and performance
条件:logic analyzers. This means we can offer the best performance, great value, and access to the industry’s broadest range of logic probing accessories.
These logic probes for the InfiniiVision mixed signal oscilloscopes (MSOs) are the same ones used with Keysight industry- leading high-performance
The N2756A 4 x
4 signal logic probes are
divided into four sets of four channels so you can probe pins that are far apart and work conveniently with only one set if that’s all you require. For optimal signal
fidelity, connect ground at each logic probe, in addition to taking a common ground to all four signals via a separate ground connector on the probe pod. The
N2756A probe is included with 3000,
4000, and 6000 X-Series MSOs.
The N2755A is an
8-channel MSO logic
probe designed to work with the
2000
条件:Samtec, and Soft Touch probes. Please note that the 01650-61607 logic probe cable is no longer available for purchase.
The 01650-61607 is the
40-pin (F) to
40-pin (F) logic probe cable for Keysight’s
InfiniiVision and 54600 Series MSOs.
This cable gives the MSO the standard
40-pin female input connector that many
Keysight logic analyzers have. With this cable, a user can connect a wide variety of logic analyzer probes such as Mictor,
Without the 01650-61607
40-pin to
40-pin cable
40-pin Mictor, Samtec or
Soft Touch probes you may already own cannot be used with InfiniiVision MSOs.
01650-61607 logic probe
N2756A
16-ch MSO cable kit
Mixed Signal Oscilloscope Logic Probes (Continued)
条件:good chance that the logic analyzer accessories you already own work with your MSO.
The InfiniiVision MSO digital channels were designed to be compatible with a wide
variety of probing accessories developed over
20 years for logic analyzers. There is a
With the addition of an optional 40-pin cable
01650-61607, the MSO accepts numerous
条件:– Route up to 16 signals to the probe and do not use the additional probe channels.
the 40-pin cable to the other side of the probe to see the other half of the signals.
– E5346A
34-channel Mictor connector probe
– E5385A
34-channel Samtec connector
– E5383A
16-channel flying lead set
– 01650-63203
16-channel termination adaptor (also available as a bundle of both
the termination adapter and the 40-pin cable with PN
10085-68701)
– E5404A
34-channel soft touch pro connectorless probe
– E5394A
34-channel soft touch connectorless probe
– E5396A
16-channel soft touch connectorless probe
– Any other accessory that connects to a logic analyzer via a
40-pin cable
For logic accessories of greater channel width than MSO digital channels
(>
16 channels), there are two use models.
– Route up to 32 signals to the probe and measure half of them at a time. Simply plug
E5396A
16-channel soft touch connectorless
E5346A 34-channel Mictor connector probe E5385A
34-channel Samtec connector probe
1147B
50-MHz current probe with AutoProbe
interface 1146B
100-kHz current probe
N2893A
100-MHz current probe with
N2780B Series current probes with N2779A
适用型号 N2780B/81B/82B/83B/83L
2-MHz/10-MHz/50-MHz/100-
The N2780B Series current probes are
high bandwidth, active current probes, featuring flat bandwidth, low noise (2.5 mArms) and low circuit insertion loss. In conjunction with the power supply
(model N2779A), these probes can be
used with any oscilloscope having a high- impedance BNC input. The companion power supply N2779A (3 x 12 Vdc output) lets you connect up to any three N2780B-
83B current probes to a single power
条件:you to reach DUTs over long distances very easily. Other than the bandwidth performance, the N2783A and N2783L have the same electrical performance.
The N2783L
80 MHz current probe
offers a
5-m long cable, which allows
The N2783L also requires the N2779A
N2779A is UL listed.
1147B/N2893A/N7026A
50-MHz/100-MHz/150-MHz
The
1147B/N2893A/N7026A have
wide bandwidth ranges, from DC to 50-MHz/100-MHz/150-MHz. The probes offer flat frequency response across the entire bandwidth range, low noise (2.5
mArms for 1147B/N2893A
250 µArms for
N7026A) and low circuit insertion loss.
These three current probes are compatible with the AutoProbe interface, which completely configures the oscilloscope for the probe. AutoProbe can
be found on the InfiniiVision
3000T X-
4000 X-, and 6000 X-Series. Probe power
is provided by the scope. The N2893A
and N7026A uniquely provide auto
demagnetization and offset elimination feature when used in conjunction with
InfiniiVision or Infiniium oscilloscopes
– Up to 150 MHz bandwidth and
500 Arms current measurement range
– Hybrid technology to measure ac and dc
– Compatible with 1 MΩ scope input
Accurate current measurements without breaking the circuit
条件:accurate display and measurement of currents from 100 mA to 100 Arms, dc to 100 kHz, without breaking into the circuit.
A battery level indicator and overload indicator help ensure proper readings. It connects directly to the scope through a 2-m coaxial cable with an insulated BNC.
Compatible with any scope or voltage measuring instruments with BNC input, the 1146B and N2780B Series current probes offer accurate and reliable solutions
for measuring dc and ac currents. The probes use a hybrid technology that includes a Hall effect sensor that senses the dc current, and a current transformer
that senses the ac current, making it unnecessary to make an electrical connection to the circuit. 1146B
100 kHz current probe
The
1146B ac/dc current probe provides
N7026A
150-MHz high sensitivity current
probe with AutoProbe interface
条件:used with an InfiniiVision or Infiniium oscilloscope, provides highly-accurate, low current waveforms for improved debug and analysis.
N7026A high sensitivity clamp-
on current probe
1 mA/div sensitivity
The N7026A is the Keysight’s highest
sensitivity clamp-on current probe. It has up to 5x lower noise than our other clamp-on current probes with 0.1V/A output voltage rate. This enables you to
measure down to 1 mA/div with much
higher accuracy. The N7026A, when
It also has a wide input range, up to 30
Arms or 40 Apk. To achieve the widest
条件:will automatically synchronize with the corresponding power source when inserting or removing the AC adapter.
AC power adapter that comes with the probe. Without the external power adapter, you can achieve up to a
5 Arms or 5 Apeak input range. The oscilloscope
For accurate measurement with a clamp-on current probe, degaussing and eliminating the offset error is critical. A degauss button is included in the design of this probe. One
push of the button will perform a degauss operation. Pushing and holding the button for
> 2 sec will perform a degauss and autozero
the DC offset. Whenever you are using the degauss button, the current sensor should be locked with no current flowing. Alternatively, the same operation can be performed from the
Improved noise floor of the N7026A (yellow trace) over the N2893A (green trace)
N7026A current probe
Clamp-on Current Probes (Continued)
Characteristics of the
1146B
Bandwidth
1 dc to 100 kHz (–3 dB)
Current range
100 mV/A:100 mA to
10 A peak
10 mV/A:1 to 100 A
Output signal
1000 mV peak max
(50 mA to 10 A peak)
Range 3% of reading ± 50 mA
10 mV/A (500 mA to 40 A peak)
Range 4% of reading ± 50 mA
10 mV/A (40 A to 100 A peak)
Accuracy (40 A to 100 A peak)
15% max at 100 A
480 μV
Insertion impedance
0.01 Ω (50/60 Hz)
Maximum working voltage
600 Vrms CAT II or 300 Vrms CAT III
Maximum common mode voltage
600 Vrms CAT II or 300 Vrms CAT III
Influence of adjacent conductor
< 0.2 mA/A AC
Influence of conductor position
< 0.2 mA/A AC
Battery
9 V alkaline (NEDA
Low battery Green LED on when
条件:Note: Reference conditions 23 ± 5 °C, (73.4
≤ 6.5 V
Battery life
55 hours typical
± 41 °C)
20 to 75% relative humidity, dc to 1 kHz
probe zeroed
1-minute warmup, batteries at
9 V + 0.1 V, external magnetic field <
40 A/m
no dc component, no external current carrying conductor, 1 MΩ/100 pF load, conductor centered in jaw.
1. Characteristics marked with asterisks are
specified 性能. Others 典型值特性
Characteristics of N2780B
Bandwidth (–3 dB) dc to 2 MHz (N2780B)
dc to 10 MHz (N2781B)
dc to 50 MHz (N2782B)
dc to 80 MHz (N2783L)
dc to 100 MHz
(N2783A)
Maximum current (continuous) 500 A (N2780B)
150 A (N2781B)
30 A
(N2782B/83B/83L)
Maximum peak current (non- continuous)
700 A peak (N2780B)
300 A peak (N2781B)
50 A peak
(N2782B/83B/83L)
Output voltage rate
0.01 V/A (N2780B/81B)
0.1 V/A
(N2782B/83B/83L)
Amplitude accuracy ± 1.0 % rdg
± 500 mA
(N2780B)
(N2781B)
(N2782B)
(N2783B/83L)
Keysight current probes 1146B 100-kHz current probe 1147B
50-MHz current probe with
N2893A
100-MHz current probe with
N7026A
150-MHz high sensitivity current
probe with AutoProbe interface
N2780B
2-MHz current probe
N2781B
10-MHz current probe
N2782B
50-MHz current probe
N2783L
80-MHz current probe with
5-m long cable
N2783B
100-MHz current probe
N2779A
3-channel power supply for
For more information about the
N2780B Series current probes, refer
to the Keysight N2780B Series current
probe data sheet, literature number
5989-6432EN.
Characteristics of the
1147B/N2893A/N7026A current probes
Bandwidth (–3 dB) DC to 50 MHz (1147B) DC to 150 MHz
DC to 100 MHz (N2893A)
Rise time (calculated, 10% to 90%) 7 nsec (Tr = 0.35/BW) 2.67 nsec (Tr =
0.4/BW)
Maximum current (continuous) 15 Apeak, 15 ADC, 10 Arms 30 ADC
30 Arms (with external power adapter)
30 Apeak, 30 ADC
24 Arms (when one
probe is used with InfiniiVision
3000XT
5000/6000/7000 scope)
5 ADC
5 Arms (without external power adapter)
Maximum peak current (non-continuous) (for pulse-widths ≤ 10 µs) 30 Apeak 40 Apeak (when using external AC power adapter)
32 Apeak (when one probe is used with
InfiniiVision 3000XT
5000/6000/7000 scope)
15 Apeak (without using external power adapter)
Output voltage rate 0.1 V/A
1 V/A and 0.2 V/A, automatically switched by the
条件:current) ± 1% rdg. ± 5 mA to 30 Arms (including calibration scale factor of oscilloscope measured at DC or 45 to 66 Hz)
Minimum oscilloscope vertical scale 10 mA/div
1 mA/div
Amplitude accuracy ± 1% rdg
± 10 mA (DC or 45 to 66 Hz, rated
Noise ≤ 2.5 mArms (for
20 MHz bandwidth measuring
≤ 250 µArms (for
20 MHz bandwidth measuring
Temperature coefficient for sensitivity
± 2% or less (within a range of 0 to 40 °C or 32 to 104 °F)
Effect of external magnetic fields Equivalent to a maximum of 20 mA (in a DC to 60 Hz
400 A/m magnetic field)
Maximum rated power
3 VA (with rated current)
Diameter of measurable conductors
5 mm dia. (0.2 in dia.)
Probe interface AutoProbe interface (1 MΩ terminated)
Cable lengths Appox.
1.5 m (59.0 in)
Maximum number of probes supported 2 (3000XT, 5000/6000/7000) 2 (3000XT
5000/6000/7000 without external
power adapter) 4 (4000X, 6000X) 4 (3000XT, 5000/6000/7000 with external power adapter) 4 (4000X
6000X)
Clamp-on Current Probes (Continued)
条件:currents ranging from a few 100 milliamps to 3,000 A from 3 Hz to > 30 MHz.
– Easy-to-use clip-around coil enabling current measurement in confined space
– Measure AC current up to 3,000 Apk (with N7040A)
– Up to 30 MHz bandwidth (with N7041A/42A)
The N7040A Series Rogowski coil current probes are designed for measuring AC
The probes have a thin, lightweight, flexible and simple-to-use clip-around Rogowski
coil that enables current measurement in the most difficult-to-reach parts and confined
spaces of a circuit under test and can measure large AC current without increase in
The N7040A Series is ideal for measuring AC current in the presence of large DC current
and can be used to design, debug and troubleshoot power semiconductor circuits,
power supplies, inverters and motor drives
These probes come with an AC power adapter and 4x AA batteries to power the probe
and can be used with any oscilloscope with 1 Mohm BNC interface.
适用型号 N7040A N7041A N7042A
HF bandwidth (—3 dB) 23 MHz 30 MHz
30 MHz
LF bandwidth (—3 dB) 3 Hz 12 Hz
9.2 Hz
Peak current (Apk) 3,000 Apk 600 Apk
300 Apk
Sensitivity 2 mV/A (500:1) 10 mV/A (100:1)
20 mV/A (50:1)
Max noise (mVpp) 8 mVpp 10 mVpp
15 mVpp
Droop (%/msec) 2.8%/msec 11%/msec
9%/msec
Peak di/dt (kA/usec) 80 kA/µsec 40 kA/µsec
20 kA/µsec
Absolute max peak di/dt (kA/µsec) 100 kA/µsec 100 kA/µsec
70 kA/µsec
Absolute max rms di/dt (kA/µsec) 1.2 kA /µsec 1.2 kA /µsec
1.2 kA /µsec
Accuracy Calibrated to ± 0.2% of reading with conductor central in the coil loop
Variation in conductor position
± 2% of reading
Linearity
0.05% of reading
DC offset
± 3 mV max at 25 ºC
Temperature range Coil and cable at —40 to +125 ºC
Coil voltage 5 kV peak 5 kV peak
1.2 kV peak
Coil length (circumference) 200 mm 100 mm
80 mm
Coil cross-section (diameter) 4.5 mm 4.5 mm
1.7 mm
Cable length
4 m (connecting cable coil to
integrator box)
2.5 m (connecting cable coil to integrator box)
Total cable length 4.5 m (4 m input cable +
0.5 m BNC
cable to scope) 3 m (2.5 m input cable +
0.5 m BNC cable to scope)
Probe output Terminated into
1 MΩ BNC input of oscilloscope
Probe power
4x AA batteries and AC power adapter (included)
N7040A/41A/42A Rogowski Coil AC Current Probes
– Measure AC/DC currents as low as
50 µA
– Ideal for capturing and analyzing low level current flow in the DUT to characterize sub-circuits or measure current consumption of battery-
powered devices or integrated circuits
条件:to make high-dynamic-range, high- sensitivity measurements to meet today’s challenging current measurement needs.
– Simultaneous high- and low-gain views of the current waveform for more precise wide dynamic range measurement (with N2820A)
As modern battery-powered devices and integrated circuits become more green and energy efficient, there is a growing need to make high-sensitivity, low-level
current measurements to ensure the current consumption of these devices is in acceptable limits. The N2820A high-sensitivity probe is engineered
The ultra-sensitive N2820A AC/DC
current probe can support measurements from 50 µA to 5 A on Keysight oscilloscopes. The N2820A interface uses a make-before-break (MBB) connector,
allowing you to quickly probe multiple locations on your DUT without having to solder or unsolder the leads. The N2820A
2-channel current probe connects to
two oscilloscope channels to provide simultaneous low-and high-gain views for wider dynamic range measurement, while the N2821A
1-channel current probe
provides one user-selectable view at a time
The N2820A 2-channel current probe connects to two oscilloscope channels to provide
simultaneous low- and high-gain views for wider dynamic range measurement
Use an area-under-the-curve measurement (Charge) on InfiniiVision oscilloscopes to easily calculate the integrated current consumptions over
条件:probes are compatible with InfiniiVision 3000 X-, 4000 X- and 6000 X-Series oscilloscopes.
The N2820A/21A high-sensitivity current
Bandwidth (–3 dB) Zoom-out channel: DC to 3 MHz
Zoom-in channel: DC to 500 kHz
Risetime (Tr = 0.35/bandwidth, 10 to 90%) Zoom-out channel: <
0.116 μs
Zoom-in channel: <
0.7 μsec
Minimum measurable current 1 250 μA (with N2822A 20 mΩ
500 mW)
50 μA (with N2824A 100 mΩ
500 mW)
5 mA (with N2825A user-defined 1 mΩ
500 mW)
50 μA (with N2825A user-defined 1 kΩ
500 mW)
Maximum measurable current 5 A (with N2822A 20 mΩ
500 mW)
2.2 A (with N2824A 100 mΩ
500 mW)
5 A 2 (with N2825A user-defined 1 mΩ
500 mW)
1.2 mA 2 (with N2825A user-defined 1 kΩ
500 mW)
DC amplitude accuracy
± 3% or 10 μA (whichever is greater)
Gain 3 Zoom-in channel: 300
± 3%
Zoom-out channel: 1.97
± 3%
Standard accessories 1 each
20 mΩ resistor sensor head
1 each
100 mΩ resistor sensor head
1 each user-defined resistor sensor head
5 each twisted leads (22 AWG) with sockets
5 each twisted leads (22 AWG) without sockets
5 each MBB headers
5 each MBB receptacles
1 each ground lead
1 each screw driver
1 each passive cable (with N2820A only)
1 each user guide manual (English)
Compatible InfiniiVision oscilloscopes InfiniiVision 3000 X-Series (with software version
2.30 or higher)
InfiniiVision 4000 X-Series (with software version
3.10 or higher)
InfiniiVision 6000 X-Series (with software version
6.00 or higher)
Max number of probes supported by
3000 X-Series Two N2820A probes using both pods or two N2821A probes
Max number of probes supported by 4000 X-Series Two N2820A probes using both pods, four N2820A probes using only the primary pod, or four
Model numbers Descriptions
N2820A High-sensitivity
2-ch current probe
N2821A High-sensitivity
1-ch current probe
N2822A
20 mΩ resistor tips
N2824A
100 mΩ resistor tips
N2825A User-defined resistor tips
N2826A Replacement wires (15.5 cm, 22 AWG bare wires) (qty
5)
N2827A Passive cable (for N2820A secondary channel)
N2828A Replacement MBB (make before break) headers (qty
5)
N2829A Replacement MBB (make before break) receptacles and 15.5 cm, AWG 22 socketed wires (qty
5 each)
< 40 Vdc + peak ac
Operating current
0.5 A maximum
Capacitance between contacts
2 pF typical (all except
Keysight-E2643A/44A)
4.33 pF typical at 1 MHz
(Keysight-E2643A/44A)
Self-inductance
15 nH typical (all except
Keysight E2643A/44A)
37 nH typical at 1 MHz
(Keysight E2642A/44A)
Cross coupling
–31 dB typical at 100 MHz
(Keysight E2643A/44A)
< 0.1 Ω
E2613A
0.5 mm Wedge probe adapter
E2614A
0.5 mm Wedge probe adapter
E2643A
0.5 mm Wedge probe adapter
E2615A
0.65 mm Wedge probe adapter
E2616A
0.65 mm Wedge probe adapter
E2644A
0.65 mm Wedge probe adapter
10072A SMT kit for 10070 probe family
An inexpensive solution for probing fine-pitch ICs, the 10072A SMT kit includes 10 IC clips and 2 dual-lead adapters that connect the clips directly to
10070-family probes.
The 10075A
0.5-mm IC clip kit is ideal
for connecting to ICs as fine as
0.5 mm.
The clip body allows many clips to be mounted side-by-side. The kit includes four 0.5-mm IC clips and two dual-lead adapters that connect the IC clips directly
to 10070-family probes.
– Mechanically non-invasive contact
– 3-
8-, and 16-signal versions
– Supports
0.5 and 0.65-mm
条件:while you are trying to operate your scope, the Wedge was designed with you in mind.
The Keysight wedge probe adapter eliminates many of the frustrations associated with probing surface mount components. If you have ever accidentally
shorted IC pins together, experienced electrical and/or mechanical problems with soldering small wires onto leads, or gotten frustrated juggling multiple probes
Make the inaccessible accessible
条件:is easy to insert and it stays put. There is no need to solder small wires onto leads.
When you use the Wedge, you do not have to worry about shorting IC pins together on a delicate component–or on an irreplaceable prototype. The Wedge
The Wedge is mechanically non-invasive, so you will not damage the legs of the
IC. Instead, you will have easy access to hard-to-reach components.
条件:Wedge’s low capacitance and inductance provides superior performance to many other alternatives.
The Wedge makes two contact points with each leg of the IC. This redundant physical connection increases the electrical reliability of the connection. The
The Wedge probe adapter connects directly to 1145A/1155A active probes and the dual lead adapter provided with the
1160A-65A passive probe family and
N2877A/N2879A accessory kits for use
with N287xA Series passive probes.
The sturdy Keysight
1180CZ Testmobile
for use with 6000 Series oscilloscopes
makes sharing your scope easy. Its large wheels make it easy to roll from place to place. For use with the Keysight
6000
Series scope, the
1180CZ Testmobile
scope cart with the N2919A bracket
provides convenient mobility and secure mounting of your scope.
Specifications for the Keysight
Total load capacity
59 kg (130 lbs)
Tilt tray 45.7 cm wide x
45.7 cm deep
条件:padded shell for shipment. For use with the 7000, 4000 X-, and 6000 X-Series, order N2733B soft carrying case.
The Keysight N6457A soft carrying case
makes transporting and shipping your 2000 X- and 3000 X-Series oscilloscope safe and simple. An oscilloscope and other accessories fit neatly inside the
The Keysight N2916B rackmount kit
positions your
5000 and 6000 Series
scope in the center of the rack. Each kit includes a custom shelf with rails, six
BNC pass-throughs and all necessary screws. For mounting the 7000 Series in the rack, order N2732A. For mounting all
2000 X- and 3000 X-Series in a rack
order N6456A. For mounting any
4000
X-Series in a rack, order N2763A. For
mounting a
6000 X-Series in a rack, order
the N2111A.
Ordering information
1180CZ Testmobile for 6000 Series
N2919A Bracket for 1180CZ Testmobile and
6000 Series scope
N2917B Hard carrying case for 5000 and
6000 Series
N6457A Soft carrying case for 2000 X- and
3000 X-Series
N2733B Soft carrying case for 7000
4000
X- and 6000 X-Series
N2760A Soft carrying case for 5000 Series
N2916B Rackmount kit for 5000 and 6000
N2732A Rackmount kit for 7000 Series
N6456A Rackmount kit for 2000 and 3000
N2763A Rackmount kit for 4000 X- Series
N2111A Rack mount kit for 6000 X-Series
N2760A soft carrying case for the
5000 Series
N2733B soft carrying case for 7000
4000 X-
and 6000 X-Series
N2916B rackmount kit for 5000/6000 Series
条件:1. Includes 3x magnifying glass, arm strap,
N2784A
1-arm probe positioner
N2785A
2-arm probe positioner
N2786A
2-leg probe positioner
N2787A
3D probe positioner
– Easy-to-manipulate probe arms for hands-free browsing
– One- or two-articulated arms with stable high-mass base (N2784A and
N2785A)
– Quick and stable XY positioning (N2786A)
– Stable
3D probe positioning for
hard-to-reach XYZ access (N2787A
– Compatible with most scope probes
条件:positioners provide quick and stable X-Y positioning for PC boards and devices that require hands-free probing.
– Applications: Hands-free browsing for electronic components on PC board
The N2784A and N2785A probe
Unlike other probe positioners that require multiple adjustments to lock the probe holder into position, the N2784A and N2785A need only the “lift and
drop” motion to put the probe in place
The weight stabilization technique used in these probe holders keeps constant pressure at the probing point so the probe tip stays in position even when the target
The N2786A is a low cost, easy-to-use
X-Y axis probe holder for general purpose probing applications. The two-legged positioner is designed to be easy to use–the positioner itself has no controls
条件:with a flexible, articulating arm that can be quickly positioned in a variety of configurations.
For more information about Keysight’s probe positioners, refer to literature number 5989-9131EN.
The N2787A is a
3D probe positioner
N2784A one-arm probe positioner
N2786A 2-leg probe positione r N2787A
3D probe positioner
T2A Probe Interface Adapter
– Enables Tektronix TekProbe-BNC level
2 probes to connect to
Keysight’s AutoProbe interface on InfiniiVision 3000 X-, 4000 X-, 6000 X-
5000
以上指标摘自厂家官方数据手册,完整定义、测试条件与保证值口径以手册为准。完整指标、测试条件与定义口径请见产品页「软件和手册 | 白皮书」栏目中的官方数据手册。
是德科技 | KEYSIGHT · onetest 仪器资源库